HydroPro, Inc. ^TM

Quality products tailored to the manufacture and repair of boilers and heat exchangers.

www.hpro.com

Tube to Tubesheet Joining Tube Setting Prior to Expansion Tube Setting Prior to Welding Sleeving Leak Testing Tube to Baffle Expansion

Feed Water Heaters

Tube to Tubesheet Joining Tube Setting Prior to Expansion Tube Setting Prior to Welding Sleeving Leak Testing Tube to Baffle Expansion

Condensers

Tube to Tubesheet Joining Tube Setting Prior to Expansion Tube Setting Prior to Welding Sleeving Leak Testing Tube to Baffle Expansion Tube to Fin Expansion

Boilers

Tube to Tubesheet Joining Tube Setting and Flaring Sleeving Leak Testing

Fin Fan Units

Tube to Tubesheet Joining Tube to Fin Expansion Tube Setting Prior to Expansion Tube Setting Prior to Welding Sleeving Leak Testing

Air Heaters

Tube to Tubesheet Joining Partial Tube Replacement

Because Partial Tube Replacement is a very unique application, we ask that you contact us to discuss you particular needs. We have done partial tube replacement in units with tubes up to 6 inches in diameter. Partial tube replacement may be a good temporary solution for you to keep an older unit online while a longer term solution is being developed. Please contact HydroPro's Engineering Department with any questions you may have.

Tube Setting Prior to Expansion Tube Setting Prior to Welding Sleeving

Sanitary and Pharmaceutical

Tube to Tubesheet Joining Tube Setting Prior to Expansion Tube Setting Prior to Welding Leak Testing Tube to Baffle Expansion

Other

If your vessel type or application is not listed, please contact our service or engineering departments for further assistance. We have extensive experience in designing and manufacturing specialty tooling to handle unique applications ranging from 1/4 in. to 12 in diameters. Click here for contact information.

PRODUCTS

HydroPro HydroPro Tooling DeltaPro HydroProof SleevePro BoilerPro TubePro Tube Plugs WeldLock

SERVICES

ENGINEERING

Tube Plug Data Sheet

Contact:		Tube Plug End User:
Date:	06/19/2013	Phone:
		Job #:

SCOPE OF APPLICATION AND SPECIFICATIONS

Number of Tubes:

Type of Unit:

Heat Exchanger
Condenser
Feedwater Heater

Boiler
Other (Describe):

Number of Plugs Required:

Approximate Start Date:

TUBES

Material:		Wall:
Yield:		Wall Thickness/Gage:
Tensile:		Actual Tube ID Measurement:
O.D.:		U-Bend or Straight:
Type:		Overall Tube Length:

Setting of Tube to Tubesheet Primary Face:
Are the Tubes to be Welded to the Tubesheet?	Yes No

TUBESHEET

Total Thickness:	Clad?	Yes No
Material:	Shell Attached?	Yes No
Yield:	Partition Plate?	Yes No
Tensile:

Distance from Tubesheet Face and Outside of Shell/Divider Plate(s)/Flange/Obstructions:

Shortest Distance Between Hole Center Line and Shell/Plate:

HOLES

Diameter:
Chamfer?	Yes No
Chamfer Location:
Degree of Chamfer:
Chamfer Depth:

GROOVES

Number:
	NOTE: As a minimum, placement of the 1st groove should begin 1/2" from the face of the tubesheet or in the center based on tubesheet thickness.
TEMA?	Yes No
	If "No", please provide specifications in the area below.
Customer Receptive to Hydraulic Expansion Groove? Yes No
	NOTE: Hydraulic expansion groove is a single wide groove (centered in sheet if possible).

LIGAMENT

Thickness:
Pitch:
Hole Pattern:

EXPANSION ZONE

Start of Expansion Inside Tubesheet:
Stop of Expansion Distance from Rear of Tubesheet:
Total Expansion Zone:

TUBE-TO-TUBESHEET WELD

Tubes to be Welded?	Yes No
If Yes, how?
Maximum Counter Sink O.D. for the Weld:

EXPANDING PRESSURE REQUIREMENTS

Hydrotest Pressure:
When welding, the following expansion procedure is recommended: 1. TubePro; setting of tube 2. Weld 3. Hydraulic Expand Note: No weld rollover is recommended

SPECIFICATIONS (IF APPLICABLE)

If you need to provide any additional drawings, sketches, blueprints, or performance requirements regarding working and test pressure of the vessel, please indicate below.

Will additional drawings be supplied? Yes No

EXTERNAL EXTENSIONS

For expansions which require going around an interference such as a channel, shell, partition plate, or any other obstruction, creating a situation where expansion would take place at a distance from the tubesheet face.

Distance from outside face of shell or plate to face of tubesheet:
Is there access for a stop collar at tubesheet face or outside of shell?	Yes No

HydroPro, Inc. TM

Quality products tailored to the manufacture and repair of boilers and heat exchangers.

www.hpro.com

Tube Plug Data Sheet

HydroPro, Inc. ^TM